Mobile
Log In Sign Up
Home > english-chinese > "spin temperature" in Chinese

Chinese translation for "spin temperature"

自旋温度

Related Translations:
spin:  vt.(spun , 〔古语〕 span; spun;spinning)1.纺。2.使(陀螺等)旋转;使(车轮)打空转〔在冰上,沙中〕。3.(蜘蛛、蚕等)吐(丝),结(网),(蚕)结(茧)。4.转镟床(等)旋制;钻孔。5.编造;讲(故事等)。6.〔俚语〕〔常用 p. p.〕使过度疲劳。7.〔美俚〕欺骗。8.〔英国〕使考不及格。9.(通过离心力作用)抛出,丢开 (off)。
spinning rotor:  离心头, 离心器
rope spining:  套索步套锁转
spinning bristle:  纺绩鬃
whip spin:  鞭打状翻腾
spin eigenstate:  自旋本宅
laura spining:  劳拉斯皮宁
scope spin:  雷达操纵员疲劳
spined loach:  花鳅;千秋鱼
spin destiny:  扭转乾坤
Example Sentences:
1.A high spin temperature , for example , would indicate that a high fraction of atoms were aligned
例如,高自旋温度代表较高比例的原子,具有相同方向的自旋排列。
2.When the spin temperature returned to equilibrium with the radiation temperature , hydrogen was neither a net absorber nor a net emitter of 21 - centimeter photons
当自旋温度回归辐射温度而达到平衡,氢气便不再吸收,也不再发射21厘米光子。
3.The pan / pu hollow fibers were successfully fabricated when the spinning temperature was controlled from 190 ? to 200 ? and the rotate speed of screw less than 70r / min
结果表明纺丝温度在190 ? 200之间,螺杆转速70r min时,能够顺利纺制pan pu中空纤维。
4.The solution had good fluidity , spinnability , dynamic stability , and would never be demixing . the original camp fibers had better water absorbability when the spinning temperature was 80 and pressure was 0 . 4mpa
纺丝温度为80 ,纺丝压力为0 . 4mpa时,以丙酮为凝固剂,经湿法纺丝成形后,得到的camp初生纤维具有较好的吸水性能。
5.Spinning temperature were controlled ranging from 190 to 205 , rotate speed of the screw was less than 70r / min , the ideal room temperature was 10 ~ 15 , and the winding speed decreased with the increase of content of baso4
纺丝温度控制在190一205之间,螺杆转速< 70r / mln ,卷绕速度则是随着baso4含量的升高而下降,实验中采取低速卷绕,纺丝理想环境温度控制在10 ~ 15 ’ c左右。
6.The influence of the melt transfer temperature , spinning temperature , temperature and speed of quench air , the 1st hot rolls temperature , the 3th hot rolls temperature , drawn ratio on dying property of melt direct spun fdy were discussed
摘要主要就熔体直接纺fdy生产过程中熔体输送温度、纺丝温度、侧吹风温度、风速、第一对热辊温度、第三对热辊温度、拉伸倍数等因素对染色性能的影响进行探讨。
7.The simulation results show that the shaped degree is decreasing when the spinning temperature and intrinsic viscosity are increasing ; the spinning speed has little effect on the shaped degree when the pump mass throughput is constant ; the shaped degree is increasing with the increasing of pump mass throughput when the spinning speed is constant ; the cross air - blow conditions have much effect on the shaped degree ; the scope of shaped cegree is increasing when the aspect ratio of spinneret hole is increasing ; the shaped degree has obvious decreasing tendency in the small zone of spinning path and this decreasing became gently when the pump mass throughput is increasing
模拟的结果表明:扁平纤维的异形度随着纺丝温度及特性黏度的升高而降低;泵供量一定时,纺速对异形度的影响不大;纺丝速度一定,异形度随着泵供量的增大而增大;吹风条件对异形度的影响较大;随着喷丝孔的长宽比的增大,异形度增加的幅度也较大;异形度在纺程上较小的区间内有明显的下降趋势,并随着泵供量的增加其下降的趋势变缓。
8.Theory therefore indicates that the dark ages were defined by three distinct temperatures : the spin temperature ( a measure of the relative abundance of atoms with different spin states ) ; the ordinary , kinetic temperature ( a measure of the motions of the atoms ) ; and the radiation temperature ( a measure of the energy of the background photons )
因此理论上,黑暗年代是由三种截然不同的温度来定义:自旋温度(不同自旋状态原子相对数目的度量) 、一般的动力温度(原子运动的度量)与辐射温度(背景光子能量的度量) 。
9.Abstract : the formation technologies , the structure and properties of tcs microporous man - made yarn - kind new polyester fibre which was spinned in tcs with some micrometallic - oxide have been studied . the results indicate that the rheological behaviour and spinnability of commixed polyester melt , and the structure and properties of the fibre , are relative to the spinning temperature , melt pressure , microporpus size for spinning , formation conditions , thermo - vascellum temperature , thermo - vascellum position and rolling speed , besides the viscosity of polyester cuts , coacervation particles , adding amount and size of micrometallic - oxide
研究表明, tcs微孔化共混聚酯熔体在成型加工中的流变行为和可纺性,及其纤维的结构性能除了与原料切片的特性粘度、凝聚粒子和共混聚酯中超细金属氧化物微粒的添加量、粒径等因素的影响有关外,还与纺丝温度、纺丝熔体压力、喷丝板微孔尺寸、冷却成形条件、热管温度、热管安装位置以及卷绕速度等因素的影响密切有关。
Similar Words:
"spin sublevel" Chinese translation, "spin susceptibility" Chinese translation, "spin susceptible" Chinese translation, "spin system" Chinese translation, "spin table" Chinese translation, "spin tensor" Chinese translation, "spin tensor operator" Chinese translation, "spin test" Chinese translation, "spin test treatment" Chinese translation, "spin tests" Chinese translation